Skip navigation

Numerical modelling of the tilt casting processes of titanium alumindes

Numerical modelling of the tilt casting processes of titanium alumindes

Wang, Hong (2008) Numerical modelling of the tilt casting processes of titanium alumindes. PhD thesis, University of Greenwich.

[img]
Preview
PDF (Pages containing signatures redacted)
Hong Wang 2008 - Redacted.pdf - Published Version
Available under License Creative Commons Attribution Non-commercial No Derivatives.

Download (45MB) | Preview

Abstract

This research has investigated the modelling and optimisation of the tilt casting process of Titanium Aluminides (TiAl). This study is carried out in parallel with the experimental research undertaken in IRC at the University of Birmingham. They propose to use tilt casting inside a vacuum chamber and attempt to combine this tilt casting process with Induction Skull Melting (ISM). A totally novel process is developing for investment casting, which is suitable for casting gamma TiAl.

As it is known, gamma TiAl alloys has great properties including low density, high specific yield strength, high specific stiffness, good oxidation resistance and good creep resistance at high temperature [Clemens -2000][Appel et at. -2000]. A worldwide research effort has been made to develop gamma TiAl because it can offer a great potential for reducing the weight of high performance components and also engine of power generation gas turbine. Titanium alloys are very reactive at molten condition, and so, they are melted in an ISM crucible in order to avoid crucible contamination. There is still a big challenge to produce a long blade, up to 40 cm, due to the low superheat provided by the Induction Skull Melting (ISM) furnace which is widely used to melt the alloys. Here computational simulation has been seen important to predict the casting defects and to help optimise the experimental process.

Computational modelling for the casting process involves a range of interactions of physical phenomena such as heat transfer, free surface fluid flow, solidification and so on. A number of free surface modelling techniques are applied to simulate the interface between the molten metal entering the mould in the filling phase, and the gas escaping.

The CFD code PHYSICA developed in the University of Greenwich is used to simulate the above physical phenomena and to simulate the fluid flow both within the rotating mould cavity/crucible assembly and in the porous mould wall (including vents).

Modelling the mould in a finite volume method is cumbersome, so an alternative 3D/1D coupled transient heat transfer model has been developed in this study. It is based on the fact that the mould filling for titanium aluminide (TiAl) is carried out during a few seconds and the thermal conductivity of the mould material is very low. Heat can be assumed to transfer mainly in a direction perpendicular to the mould wall ID. ID transient heat transfer model is governed by ID heat conduction equation in the mould part where the coordinates of each defined cell centre were calculated rather than meshing them. The coupling method between ID and 3D model is presented. The model is then validated using two simple geometries which describe two similar states in the mould filling as test cases. It has been applied to model short thin and long blades, especially to obtain accurate thermal boundaries. Comparisons with experiments have also been done. Across the presentation of the results, the factors affect the quality of the casting in the mould filling have been discussed.

This thesis also presents a novel Counter Diffusion Method which was developed with suggestions from my supervisors as a corrective mechanism to counter numerical diffusion. This is a novel method to discretise the free surface equation fully implicitly in a fast, efficient way without numerical diffusion. Validation of the novel method was undertaken against the classical collapsing column experiment. The results showed that they are in good agreement. Then the method has been used to model a long thin blade for TiAl. A huge reduction in computational time is seen when the geometry is complex and massive amount of mesh cells are generated. That greatly speeds up the simulations.

Solidification is modeled during the cooling which is following the filling stage. Gap formation between metal and mould is covered and the effects of the gap and gap size are presented by the application of model on a long twisted turbine blade.

Item Type: Thesis (PhD)
Additional Information: uk.bl.ethos.549808
Uncontrolled Keywords: titanium alumindes, numerical modelling, heat transfer, numerical diffusion,
Subjects: Q Science > QA Mathematics
Q Science > QA Mathematics > QA75 Electronic computers. Computer science
T Technology > TS Manufactures
Pre-2014 Departments: School of Computing & Mathematical Sciences
School of Computing & Mathematical Sciences > Centre for Numerical Modelling & Process Analysis
Last Modified: 08 Mar 2017 12:38
URI: http://gala.gre.ac.uk/id/eprint/6336

Actions (login required)

View Item View Item

Downloads

Downloads per month over past year

View more statistics